![]() It allows users to extend a local area network via existing coax cables, and therefore provides an inexpensive option for a fast wired, Internet connection. using the cable instead of air as transmission medium.Īnother more "hackish" solution could be to use Powerline adapters and run them on the Coax cable, similar to how this article describes running Ethernet over a phone cable.Comtrend’s G.hn Ethernet over Coax Adapter is the first G.hn standards compliant Ethernet over Coax adapter. I'm not sure, but AFAIK you could probably use more than 2 wifi adapters on a single cable. Here's an older (2006?) website where someone has done this. basically buy 2 Wifi adapters with an external antenna (usually RP-SMA) and instead of using the antenna connect it to your coax cable (e.g. The speed seems to be limited to 200 Mbps, though.Īnother option could be to run a Wifi over Coax. There's also DOCSIS which AFAIK is used for cable internet (at least in the EU?) but for all that I understand this is absolute overkill for a home installation.įar cheaper are "DECA" (DirectTV Ethernet to Coax Adapters). There's also "HomePNA" and "G.Hn" but the devices seem to be similar expensive. but the devices that I could find (even the ones for 400Mbps) are quite expensive (starting at 70€, Nov 2018). One "popular" (= easy to stumble upon) option seems to be MoCA. I'm currently facing the same issue just that the house is rented and thus I have no plan B.įor one, there's even a Wikipedia article about Ethernet over Coax. Note that you may or may not have perfect success with this, depending on whether the holes for the cable are big enough to accommodate both coax and network cable, so it might be best to try it first in a room where you'll never need coax (just in case you can't pull the coax back through from the room to the wiring closet). ![]() To pull the coax back into place, retape just the rope to the coax then go back to the wiring closet and pull until the coax is back. If that's the case, you can tape the end of your network cable and the end of a rope to the end of the coax in your wiring closet, then pull on the other end of the coax until the network cable and rope are through. In some houses, it's not easy to run new cable. If you need multiple connections in one room, you can save on wireless adapters and configure a router running DD-WRT (or your favorite open router firmware) to bridge your wired and wireless networks. There's another alternative that I'm surprised nobody else has mentioned: just install WiFi. Also, I have all these super-snazzy gigabit adaptors I'd like to be using. While I think I'd get major style points for that, I don't think I can get a 10BASE2 adapter for the new laptop. Also, I could just scare up a mess of old 10BASE2 cards and run the house on thinnet, all mid-90s style. While tempting, that sounds like more work than I really want to put in, so I'm calling that Plan B. (There are a few other options that suggest themselves - first, I could just use the existing cabling channels and re-run cat5 or 6 through the walls. Had anyone else done this? Any suggestions? My fantasy would be if you could get some kind of adapter-plug-thing that would take a coax plug on one side and a cat5/RJ45 plug on the other. What I would love to be able to do is drop a switch in the wiring closet and run 100/1000BASE-T ethernet over the coax in the walls I wouldn't otherwise be using. Of course, my problem is that I only own the one TV. The cabling is gorgeous - there's even a wiring cabinet of sorts in a closet where the cables all tie together to the splitter to the outside line. One of the features that got built in was a cable TV drop in every room. It's reasonably new - built in the early '00s.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |